Discover ways to make a DIY framed mirror to your lavatory in just some simple steps!
Our townhouse is the definition of “has good bones, however wants a whole lot of assist cosmetically.” We knew that after we moved in and have been engaged on reworking your entire home one room at a time. I’m thrilled to say that we’ve lastly made it to my little haven, our major bed room.
Once we first began engaged on our major bed room, one venture I knew I needed to finish was framing within the self-importance mirror. It’s a reasonably easy venture, so I used to be excited to make a huge impact with out an enormous quantity of labor.
We began out with simply your common, plain, builder-grade mirror:
However I knew we might give it a bit facelift with this straightforward DIY framing venture! Right here’s how we did it…
Body a Lavatory Mirror Step-by-Step
This publish accommodates affiliate hyperlinks. For extra info, see my disclosures right here.
1. Collect your provides.
The very first thing we did was be certain we had all the instruments and provides crucial to border within the lavatory mirror.
DIY Framed Mirror Provides and Instruments
2. Make your cuts on the baseboard items.
After we had gathered our provides, we wanted to chop down the baseboards we have been utilizing to assemble the body for the mirror.
We measured the outer dimensions of our mirror and used the miter noticed to chop our baseboard items at a 45-degree angle, with the surface edge the identical dimensions because the mirror.
The within size of baseboard ended up shorter than the size of the mirror to compensate for the angle lower. Once we completed slicing our baseboard items, they appeared like this:
3. Double test the lower boards.
After the framing items have been lower, we double checked to ensure they match by bodily holding them up in opposition to the mirror earlier than we did anything. We didn’t wish to make it additional alongside within the course of, solely to comprehend that we had the fallacious sizing for our body!
4. Make notches for the mirror clips (if relevant).
At this level, we additionally needed to modify our framing items for the mirror clips. Oh, the clips…
In case your mirror was hung with out clips, you win! Go get your self a prize! 😉
Since our mirror did, in actual fact, have clips, we needed to mark our baseboard items on the spot the place the clips hit. Then we have been capable of chisel out a notch for the clips in order that our body would sit flush in opposition to the mirror.
Donnie used a pointy 1/2″ wooden chisel to create the notches– it solely took a couple of minutes!
5. Assemble the body for the mirror.
Now that our baseboards have been lower and chiseled, they have been prepared to attach! We used Liquid Nails to stick the framing items collectively. Then we duct taped the corners to carry them in place whereas they dried in a single day.
6. Add shoe molding, if desired.
You don’t have so as to add shoe molding should you favor a flatter face to your mirror body. We needed so as to add some dimension and thought it gave our body a extra completed look, so we determined so as to add the layer of shoe molding to the bottom of the body.
As soon as we measured and lower our molding, once more utilizing a 45-degree angle, we used wooden glue to stick the molding to the body.
We then clamped the molding to the baseboard items to make sure that they’d adhere. (In the event you run out of clamps, you possibly can simply begin stacking stuff on the items like we did. 😉 )
We have been certain to permit the glue to dry fully earlier than we did anything to the body.
7. Paint and cling the DIY mirror body.
When the wooden glue had completed drying, it was time to color. I attempted to take the simple route and simply paint the entrance of our body. However I quickly came upon that because the mirror is reflective (duh!), we might see the the edging of the again of the body, so we wanted to color each side.
As soon as our coats of paint have been fully dry, we hung the body on the mirror utilizing Liquid Nails.
- Don’t unfold the Liquid Nails too near the within fringe of the body or, once more, it is possible for you to to see it within the mirror’s reflection.
- As soon as our mirror was affixed, we used masking tape to assist maintain it to the wall in a single day whereas the Liquid Nails dried.
8. Get pleasure from your newly framed Lavatory Mirror!
Within the morning, I nervously pulled off the masking tape, hoping not one of the paint would include it. It didn’t, I used to be relieved, and I had a wonderful framed-in mirror that I simply liked! Glad dance!
Simply because it’s my favourite a part of any transformation, let’s check out the earlier than and after!
Love! I’m all the time amazed at how such a easy venture can find yourself making an enormous distinction within the area. You probably have a builder grade lavatory mirror that would use a bit pick-me-up, this can be a nice venture to attempt! (You possibly can study extra about how we remodeled the underside a part of the self-importance right here.) We hope this tutorial will probably be useful for you!
Need to save this publish to revisit later? Make sure you pin the picture beneath so you’ll find it simply!
Have you ever performed any enjoyable DIY tasks currently?
Thanks a lot for following alongside! Have a beautiful day!
Disclaimer: We aren’t skilled carpenters, simply householders who like to DIY each time potential! Please be secure and try all tasks at your personal threat.
This publish accommodates an affiliate hyperlink. View my disclosures right here.
